CONTENTS

�1���� Introduction and scope
�2���� References
������� 2.1���� Normative references
������� 2.2���� Informative references
�3���� Definitions and abbreviations
�4���� Physical layer
������� 4.1���� Circuits
������� 4.2���� Character formatting
������� 4.3���� Data rates
�5���� Syntax and procedures
������� 5.1���� Alphabet
������� 5.2���� DTE commands lines
����������������� 5.2.1���� Command line general format
����������������� 5.2.2���� Command line editing
����������������� 5.2.3���� Command line echo
����������������� 5.2.4���� Repeating a command line
����������������� 5.2.5���� Types of DTE commands
����������������� 5.2.6���� DTE command syntax
������� 5.3���� Basic syntax commands
����������������� 5.3.1���� Basic syntax command format
� ����������������5.3.2���� S-parameters
������� 5.4���� Extended syntax commands
����������������� 5.4.1���� Command naming rules
����������������� 5.4.2���� Values
����������������� 5.4.3���� Action commands
����������������� 5.4.4���� Parameter commands
����������������� 5.4.5���� Additional syntax rules
������� 5.5���� Issuing commands
������� 5.6���� Executing commands
����������������� 5.6.1���� Aborting commands
����������������� 5.6.2���� Handling of invalid numbers and S-parameter values
������� 5.7 ����DCE responses
����������������� 5.7.1���� Responses
����������������� 5.7.2���� Extended syntax result codes
����������������� 5.7.3���� Information text formats for test commands
������� 5.8���� Manufacturer-specific characteristics
����������������� 5.8.1���� Extensions
����������������� 5.8.2���� Behavioural differences
�6���� Functions
������� 6.1���� Generic DCE control
����������������� 6.1.1���� Reset to default configuration
����������������� 6.1.2���� Set to factory-defined configuration
����� ������������6.1.3���� Request identification information
����������������� 6.1.4���� Request manufacturer identification (+GMI)
����������������� 6.1.5���� Request model identification (+GMM)
����������������� 6.1.6���� Request revision identification (+GMR)
����������������� 6.1.7���� Request product serial number identification (+GSN)
����������������� 6.1.8���� Request global object identification (+GOI)
����������������� 6.1.9���� Request complete capabilities list (+GCAP)
���������������� 6.1.10���� Country of installation, (+GCI)
������� 6.2���� DTE-DCE interface commands
����������������� 6.2.1���� Command line termination character
����������������� 6.2.2���� Response formatting character
����������������� 6.2.3���� Command line editing character
�� ���������������6.2.4���� Command echo
����������������� 6.2.5���� Result code suppression
����������������� 6.2.6���� DCE response format
����������������� 6.2.7���� Result code selection and call progress monitoring control
����������������� 6.2.8���� Circuit 109 (Received line signal detector) behaviour
����������������� 6.2.9���� Circuit 108 (Data terminal ready) behaviour
���������������� 6.2.10���� Fixed DTE rate (+IPR)
���������������� 6.2.11���� DTE-DCE character framing (+ICF)
���������������� 6.2.12���� DTE-DCE local flow control (+IFC)
���������������� 6.2.13���� DTE-DCE local rate reporting (+ILRR)
���������������� 6.2.14���� +ICLOK Select Sync Transmit Clock Source
���������������� 6.2.15���� +ILSD Select Long Space Disconnect Option
����������� �����6.2.16���� +IDSR Select Data Set Ready Option
���������������� 6.2.17���� +IRTS Select Synchronous Mode RTS Option
������� 6.3���� Call control
����������������� 6.3.1���� Dial
����������������� 6.3.2���� Select tone dialling (command)
�������������� ���6.3.3���� Select pulse dialling (command)
����������������� 6.3.4���� Incoming call indication
����������������� 6.3.5���� Answer
����������������� 6.3.6���� Hook control
����������������� 6.3.7���� Return to online data state
����������������� 6.3.8�� ��Automatic answer
����������������� 6.3.9���� Pause before blind dialling
���������������� 6.3.10���� Connection completion timeout
���������������� 6.3.11���� Comma dial modifier time
���������������� 6.3.12���� Automatic disconnect delay
�������������� ��6.3.13���� Monitor speaker loudness
���������������� 6.3.14���� Monitor speaker mode
���������������� 6.3.15���� +ASTO Store Telephone Number
������� 6.4���� Modulation control commands
����������������� 6.4.1���� Modulation selection (+MS)
������������ �����6.4.2���� Modulation automode control (+MA)
����������������� 6.4.3���� Modulation reporting control (+MR)
����������������� 6.4.4���� V.18 Selection (+MV18S)
����������������� 6.4.5���� V.18 Reporting control (+MV18R)
����������������� 6.4.6���� V.18 Answering message editing (+MV18AM)
����������������� 6.4.7���� Order of probes (+MV18P)
������� 6.5���� Error control commands
����������������� 6.5.1���� Error control selection (+ES)
����������������� 6.5.2���� Break handling in error control operation (+EB)
����������������� 6.5.3���� Selective repeat (+ESR)
����������������� 6.5.4���� 32-bit frame check sequence (+EFCS)
����������������� 6.5.5���� Error control reporting (+ER)
����������������� 6.5.6���� Call termination buffer management (+ETBM)
��� ��������������6.5.7���� +EWIND Window Size
����������������� 6.5.8���� +EFRAM Frame Length
������� 6.6���� Data compression commands
����������������� 6.6.1���� Data compression (+DS)
����������������� 6.6.2���� Data compression reporting (+DR)
������� 6.7���� DCE testing
����������������� 6.7.1���� List of Test Commands and Parameters
����������������� 6.7.2���� Test Commands and Parameters
Annex A � Procedure for DTE-controlled call negotiation
������� A.1���� Introduction
������� A.2���� Additional references and definitions
������� A.3���� Functions
������� A.4���� Definitions and conventions
������� A.5���� Commands
����������������� A.5.1���� V.8 and V.8 bis operation controls, +A8E
����������������� A.5.2���� Send V.8 menu signals
����������������� A.5.3���� Send V.8 bis signal and/or message(s)
������� A.6���� V.8 signal indications
����������������� A.6.1���� CI signal indication, +A8I
����������������� A.6.2���� Calling tone indication, +A8C
����������������� A.6.3���� Answer signal indication, +A8A
����������������� A.6.4���� V.8 negotiation complete, +A8J
����������������� A.6.5���� V.8 menu report, +A8M
����������������� A.6.6���� V.8 bis signal and message reporting
������� A.7���� V.8 origination procedures
����������������� A.7.1���� Configuration before the Dial command
����������������� A.7.2���� Operation after dialling is completed
����������������� A.7.3���� Answering signal detection
����������������� A.7.4���� V.8 abort
����������������� A.7.5���� CM signal generation
����������������� A.7.6���� JM signal detection
����������������� A.7.7���� Transition to communications
������� A.8���� V.8 Answer procedures
����������������� A.8.1���� Configuration before the Answer command
����������������� A.8.2���� Operation after the Answer command
� ����������������A.8.3���� Calling signal detection
����������������� A.8.4���� JM signal generation
����������������� A.8.5���� V.8 abort
����������������� A.8.6���� Transition to communications
������� A.9���� V.8 bis procedures
����������������� A.9.1�� ��Initiation
����������������� A.9.2���� Reception
����������������� A.9.3���� Transmission
����������������� A.9.4���� Termination
������ A.10���� Sample sessions
���������������� A.10.1���� V.8 origination, connect as V.34 transmit and receive data
���� ������������A.10.2���� V.8 answer, preconfigure for facsimile, but adaptively connect as a V.34 data modem
���������������� A.10.3���� V.8 bis sample session, based on Figure II.4/V.8 bis
Appendix I � Summary of basic and extended format commands
Appendix II � DCE configuration, dialling, negotiation and reporting, example session
Appendix III � Encapsulation of V.25 ter messages in V.25 bis DCE
����� III.1���� Scope
����� III.2���� Encapsulation of V.25 ter messages
����� III.3���� Applicable V.25 ter commands
����� III.4���� Applicable V.25 ter responses
Appendix IV � Areas reserved for further study