�1���� General
������� 1.1���� References
������� 1.2���� Abbreviations
������� 1.3���� Definitions
������� 1.4���� Reference point naming
������� 1.5���� Reference point information naming
������� 1.6���� Atomic function naming and diagrammatic conventions
������� 1.7���� Atomic function process allocation
������� 1.8���� Combination rules
������� 1.9���� Fault management and performance monitoring naming
������
1.10���� Fault management and
performance monitoring specification techniques
������ 1.11���� Performance and reliability
�2����
Supervision processes and management information flows
������� 2.1���� Information flow (XXX_MI) across the XXX_MP reference points
������� 2.2���� Supervision
������� 2.3���� Generic processes
�3����
SDH physical layer
������� 3.1���� Connection
������� 3.2���� Termination: OSn_TT
and ESn_TT
������� 3.3���� Adaptation
������� 3.4���� Sublayer functions (N/A)
�4����
Regenerator section layer
������� 4.1���� Connection (Not/Applicable)
������� 4.2���� Termination: RSn_TT
������� 4.3���� Adaptation
������� 4.4���� Sublayer functions (N/A)
�5����
Multiplex section layer
������� 5.1���� Connection (N/A)
������� 5.2���� Termination: MSn_TT
������� 5.3���� Adaptation
������� 5.4���� Sublayer functions
�6����
Higher order SDH path (Sn)
layer
������� 6.1���� Connection Functions: Sn_C
������� 6.2���� Termination functions: Sn_TT,
Snm_TT and Sns_TT
������� 6.3���� Adaptation functions
������� 6.4���� Sublayer functions
�7����
Lower order SDH path (Sm)
layer
������� 7.1���� Connection functions: Sm_C
������� 7.2���� Termination functions: Sm_TT,
Smm_TT and Sms_TT
������� 7.3���� Adaptation functions
������� 7.4���� Sublayer functions
�8 ����Compound functions
������� 8.1���� Transport Terminal Function (TTF)
������� 8.2���� Higher Order Interface (HOI)
������� 8.3���� Lower Order Interface (LOI)
������� 8.4���� Higher Order Assembler (HOA)
�9����
Timing functions
������� 9.1���� Synchronous Equipment Timing Source (SETS) function
������� 9.2���� Synchronous Equipment Timing Physical Interface (SETPI)
function
10���� Specification of jitter and
wander
������ 10.1���� STM-N interfaces
������ 10.2���� PDH interfaces
11���� Overhead Access Function (OHA)
Annex A �� Multiplex Section Protection
(MSP) protocol, commands and operation
������� A.1���� MSP Protocol
������� A.2���� MSP commands
������� A.3���� Switch operation
Annex B � Multiplex section protection (MSP) 1 + 1 optimized protocol,� commands and operation
������� B.1���� 1 + 1 bidirectional switching optimized for a network using
predominantly 1 + 1 bidirectional switching
������� B.2���� Switch commands
������� B.3���� Switch operation
Annex C � Algorithm for pointer detection
������� C.1���� Pointer interpretation
������� C.2���� Concatenated payloads
������� C.3���� Pointer processing flow chart
Annex D � PDH physical section layers
������� D.1���� PDH physical section layer (Eq)
Appendix I � Example of F1 byte usage
Appendix II � CM configuration examples
Appendix III � Example of remote indication operation
����� III.1���� Remote Defect Indication (RDI)
����� III.2���� Remote Error Indication (REI)
Appendix IV � Alarm Indication Signal (AIS)
Appendix V � Signal Fail (SF) and Signal Degrade (SD)
������� V.1���� Server Signal Fail (SSF) signal
������� V.2���� Server Signal Degrade (aSSD) signal
������� V.3���� Trail Signal Fail (TSF) signal
������� V.4���� Trail Signal Degrade (TSD) signal
Appendix VI � Data Communications Channel (DCC)
Appendix VII � Atomic function modelling of basic functions from 1994 G.783