Policy on Intellectual Property Right (IPR)
Annex
�1���� Introduction
�2���� Terms and definitions for the purpose of this Recommendation
������� 2.1���� Antenna diagram for fixed reception
������� 2.2���� Antenna factor
������� 2.3���� Bit error ratio
������� 2.4���� Cell
������� 2.5���� C/N
������� 2.6���� Coverage area
������� 2.7���� Service area
������� 2.8���� Coverage prediction
������� 2.9���� Crest factor
������ 2.10���� Directional discrimination
������ 2.11���� Guard interval
������ 2.12���� Height loss
������ 2.13���� Interfering field strength
������ 2.14���� Median
������ 2.15���� Minimum median field strength (Emed)
������ 2.16���� MFN
������ 2.17���� Minimum equivalent signal level
������ 2.18���� Minimum wanted (equivalent) field strength (Emin)
������ 2.19���� Network gain
������ 2.20���� Protection ratio
������ 2.21���� Quasi error-free reception
������ 2.22���� Receiving field strength
������ 2.23���� Receiving scenario
������ 2.24���� Reception channel
������ 2.25���� The GE06 Agreement
������ 2.26���� Self-interference inside an SFN
������ 2.27���� Single-frequency network
������ 2.28���� Standard deviation
������ 2.29���� Standard deviation of the spectral amplitudes (σsp)
������ 2.30���� σsp‑correction (Cσ)
������ 2.31���� Small area
������ 2.32���� Substitution transmitter
������ 2.33���� Synchronisation
������ 2.34���� System variant
������ 2.35���� Wanted field strength
�3���� Measurement methods
Attachment 1 to the Annex� Verifying the coverage prediction for fixed
reception
������ A1.1���� Selection of measurement locations
������ A1.2���� Necessary measurement equipment
������ A1.3���� Required information
������ A1.4���� Measurement setup
������ A1.5���� Measurement procedure
������ A1.6���� External interference
������ A1.7���� Evaluation of the results
����������������� A1.7.1���� Verifying homogeneous field strength distribution
����������������� A1.7.2���� Correction for the reception channel
����������������� A1.7.3���� Correction for time probability of interfering
signals
����������������� A1.7.4���� Calculation of the total field strength
����������������� A1.7.5���� Decision whether a measurement point is covered
������ A1.8���� Result presentation
������ A1.9���� Verification of planned coverage
Attachment 2 to the Annex� Verifying the coverage prediction for portable
reception
������ A2.1���� Measurement principle
Example:
������ A2.2� ���Necessary measurement equipment
������ A2.3���� Measurement procedure
������ A2.4���� Evaluation of the results
������ A2.5���� Result presentation
Attachment 3 to the Annex� Alternative method to determine the coverage border
of� DVB-T/T2 transmitters and networks for specific cases
������ A3.1���� Introduction
������ A3.2���� Measured parameters of the signal
������ A3.3���� Equipment requirements
������ A3.4���� Measurement planning
������ A3.5���� Measurement procedure
������ A3.6���� Processing of measurement results
������ A3.7���� Measurements in SFN
Attachment 4 to the Annex� Method to measure the coverage of DVB-T/T2 service
for� fixed reception in defined areas
������ A4.1���� Introduction
������ A4.2���� Equipment requirements
������ A4.3���� Measurement planning
������ A4.4���� Measurement procedure
������ A4.5���� Processing of the measurements
������ A4.6���� Display of measurement results
Attachment 5 to the Annex� Required corrections of measurement results
������ A5.1���� Reception channel correction (σsp‑correction)
������ A5.2���� Location probability correction
������ A5.3���� Total correction for indoor coverage